S_WipeFourWedges Performs a wipe transition between two input clips using a pattern of four wedges merging into an 'X' shape. The Wipe Percent parameter should be animated to control the transition speed. Increase the Border Width parameter to draw a border at the wipe transition edges. In the Sapphire Transitions effects submenu. Inputs: Foreground:  The current layer.   Starts the transition with this clip. Background:  Defaults to None.   Ends the transition with this clip. If this input is not provided, a fully transparent background is used, showing whatever is behind it.

Parameters:

Transition Dir:   Popup menu,  Default: Wipe Off to Bg.
Selects the direction of the transition.

Wipe Off to Bg:  transitions from the current layer to the Background.

Wipe On from Bg:  transitions from the Background to the current layer.

Auto Trans:   Popup YES-NO,  Default: No.
If enabled, a transition is performed automatically between the first and last frames of the layer. If this is off, the transition is performed manually by animating the Wipe Percent parameter.

Wipe Percent:   Default: 0,  Range: 0 to 100.
Auto Trans must be disabled for this parameter to be used. It determines the transition ratio between the From and To inputs, and would normally be animated from 0 to 100 to perform a complete transition. The curve controlling this parameter can be adjusted for more detailed control over the timing of the wipe.

Wipe Direction:   Popup menu,  Default: Wedge In.
Selects the direction of motion of the wedges.

Wedge In:  the wedges contains the first image and shrinks inwards.

Wedge Out:  the wedges contains the second image and grows outwards.

Edge Softness:   Default: 0,  Range: 0 or greater.
The width of the transition edges. Larger values will cause softer, less visible edges in the wipe pattern.

Angle:   Default: 0,  Range: any.
The rotation angle in degrees of the wedge pattern.

Aspect Scale:   Default: 1,  Range: 0.01 or greater.
Scales the aspect ratio of the wedge pattern. Increase to stretch the shapes in the horizontal direction.

Border Width:   Default: 0,  Range: 0 or greater.
If positive, a colored border is drawn at the wipe transition edges, using the border color, opacity, softness, and shift parameters below.

Border Color:   Default rgb: [0.75 0 0].
The color of the border. This has no effect unless Border Width is positive.

Border Opacity:   Default: 1,  Range: 0 to 1.
The opacity of the border. Decrease to make the border transparent and allow the image under it to show through. This has no effect unless Border Width is positive.

Border Softness:   Default: 0,  Range: 0 or greater.
The softness of the border edges. This has no effect unless Border Width is positive.

Border Shift:   Default: 0,  Range: any.
Shifts the border ahead of or behind the transition edge. This has no effect unless Border Width is positive.

Opacity:   Popup menu,  Default: Normal.
Determines the method used for dealing with opacity/transparency.

All Opaque:  Use this option to render slightly faster when the input image is fully opaque with no transparency (alpha=1).

Normal:  Process opacity normally.

As Premult:  Process as if the image is already in premultiplied form (colors have been scaled by opacity). This option also renders slightly faster than Normal mode, but the results will also be in premultiplied form, which is sometimes less correct.

Show Angle: Check-box, Default: off.
Turns on or off the screen user interface for adjusting the Opacity parameter.This parameter only appears on AE and Premiere, where on-screen widgets are supported.

See Also:

WipeLine WipeCircle WipeRectangle WipeStar WipeClock WipeWedge WipeDoubleWedge WipeDots WipeChecker WipeStripes WipeRings WipeBlobs WipeCells WipeTiles WipePixelate WipeDiffuse WipeBubble WipeClouds

Sapphire Plug-ins Introduction

© 2007, GenArts, Inc. All rights reserved.