S_WipeDots

Performs a wipe transition between two input clips using a grid of growing or shrinking dots. The Wipe Percent parameter should be animated to control the transition speed. Increase the Grad Add parameter to make the timing of the dots pattern move across the screen during the wipe. Increase the Border Width parameter to draw a border at the wipe transition edges.

In the Sapphire Transitions effects submenu.


Inputs:

Foreground:  The current layer.   Starts the transition with this clip.

Background:  Defaults to None.   Ends the transition with this clip. If this input is not provided, a fully transparent background is used, showing whatever is behind it.
        

Parameters:

Transition Dir:   Popup menu,  Default: Wipe Off to Bg.
Selects the direction of the transition.
Wipe Off to Bg:  transitions from the current layer to the Background.
Wipe On from Bg:  transitions from the Background to the current layer.

Auto Trans:   Popup YES-NO,  Default: No.
If enabled, a transition is performed automatically between the first and last frames of the layer. If this is off, the transition is performed manually by animating the Wipe Percent parameter.

Wipe Percent:   Default: 0,  Range: 0 to 100.
Auto Trans must be disabled for this parameter to be used. It determines the transition ratio between the From and To inputs, and would normally be animated from 0 to 100 to perform a complete transition. The curve controlling this parameter can be adjusted for more detailed control over the timing of the wipe.

Dots:   Popup menu,  Default: Grow.
The direction of the dots transition.
Shrink:  the dots start large and shrink inwards.
Grow:  the dots start small and grow outwards.

Edge Softness:   Default: 0,  Range: 0 or greater.
The width of the transition edges. Larger values will cause softer, less visible edges in the wipe pattern.

Angle:   Default: 45,  Range: any.
The rotation of the overall dots pattern used for the wipe, in degrees.

Frequency:   Default: 6,  Range: 0.1 or greater.
The frequency of the dots pattern. Increase for more and smaller dots, or decrease for fewer and larger.

Rel Width:   Default: 1,  Range: 0.1 or greater.
The relative horizontal size of the dots. Increase for wider dots, decrease for taller ones.

Rel Wid Pre Rot:   Default: 1,  Range: 0.1 or greater.
The relative size of the dots in the direction of the current rotation angle. If the Angle parameter is zero this will have the same effect as Rel Width.

Shift:   X & Y,   Default: [360 243],  Range: any.
Translation of the dots pattern.

Grad Add:   Default: 0,  Range: -10 to 10.
If positive, a gradient will be added to the timing of the transition pattern so it moves across the screen during the wipe. This parameter can be adjusted using the Wipe Widget if enabled, but the value must be positive to make this widget visible.

Grad Angle:   Default: 0,  Range: any.
The direction of the wipe gradient in degrees. This will have no effect unless Grad Add is positive. The Wipe Widget also allows adjusting this parameter.

Border Width:   Default: 0,  Range: 0 or greater.
If positive, a colored border is drawn at the wipe transition edges, using the border color, opacity, softness, and shift parameters below.

Border Color:   Default rgb: [0.75 0 0].
The color of the border. This has no effect unless Border Width is positive.

Border Opacity:   Default: 1,  Range: 0 to 1.
The opacity of the border. Decrease to make the border transparent and allow the image under it to show through. This has no effect unless Border Width is positive.

Border Softness:   Default: 0,  Range: 0 or greater.
The softness of the border edges. This has no effect unless Border Width is positive.

Border Shift:   Default: 0,  Range: any.
Shifts the border ahead of or behind the transition edge. This has no effect unless Border Width is positive.

Opacity:   Popup menu,  Default: Normal.
Determines the method used for dealing with opacity/transparency.
All Opaque:  Use this option to render slightly faster when the input image is fully opaque with no transparency (alpha=1).
Normal:  Process opacity normally.
As Premult:  Process as if the image is already in premultiplied form (colors have been scaled by opacity). This option also renders slightly faster than Normal mode, but the results will also be in premultiplied form, which is sometimes less correct.

Show Wipe: Check-box, Default: off.
Turns on or off the screen user interface widget for adjusting the Grad Add, Grad Angle, and Wipe Percent parameters. The value of the Grad Add parameter must first be positive for this widget to be visible.This parameter only appears on AE and Premiere, where on-screen widgets are supported.

See Also:

WipeLine
WipeCircle
WipeRectangle
WipeStar
WipeClock
WipeWedge
WipeDoubleWedge
WipeFourWedges
WipeChecker
WipeStripes
WipeRings
WipeBlobs
WipeCells
WipeTiles
WipePixelate
WipeDiffuse
WipeBubble
WipeClouds
HalfTone
Sapphire Plug-ins Introduction


© 2007, GenArts, Inc. All rights reserved.