Transitions from the first clip to the second using a
moving cloud texture. The Wipe Percent parameter should be animated to
control the transition speed.
In the Sapphire Transitions effects submenu.
Foreground: The current layer. Starts the transition with this clip.
Background: Defaults to None. Ends the transition with this clip. If this input is
not provided, a fully transparent background is used, showing
whatever is behind it.
- Transition Dir:
Popup menu, Default: Wipe Off to Bg.
Selects the direction of the transition.
- Wipe Off to Bg: transitions from the current layer to the Background.
- Wipe On from Bg: transitions from the Background to the current layer.
- Auto Trans:
Popup YES-NO, Default: No.
If enabled, a transition is performed automatically between
the first and last frames of the layer. If this is off, the transition is
performed manually by animating the Wipe Percent parameter.
- Wipe Percent: Default: 0, Range: 0 to 100.
Auto Trans must be disabled for this parameter to be
used. It determines the transition ratio between the From and To
inputs, and would normally be animated from 0 to 100 to perform a
complete transition. The curve controlling this parameter can be adjusted
for more detailed control over the timing of the wipe.
- Frequency: Default: 2, Range: 0.1 or greater.
The frequency of the clouds pattern. Increase for more
and smaller clouds, or decrease for fewer and larger.
- Frequency Rel X: Default: 0.4, Range: 0.01 or greater.
The relative horizontal frequency of the texture.
Increase to stretch it vertically or decrease to stretch it
- Octaves: Integer, Default: 8, Range: 1 to 10.
The number of summed layers of noise. Each octave is twice
the frequency and half the amplitude of the previous. A single octave
gives a smooth texture. Adding octaves makes the result approach a
fractal (1/f) noise texture.
- Seed: Default: 0.23, Range: 0 or greater.
Used to initialize the random number generator. The actual
seed value is not significant, but different seeds give different
results and the same value should give a repeatable result.
- Shift Start: X & Y, Default: [0 0], Range: any.
Translation offset of the texture. Since the texture is
procedurally generated it can be shifted with no repeating units or
- Shift Speed: X & Y, Default: [720 0], Range: any.
Translation speed of the texture. If non-zero, the
result is automatically animated to shift at this rate. The result
of animated Speed values may not be intuitive, so for variable
speed motion it is usually best to set this to 0 and animate the
Shift Start values instead.
- Grad Add: Default: 0, Range: -10 to 10.
If positive, a gradient will be added to the timing of
the transition pattern so it moves across the screen during the
wipe. This parameter can be adjusted using the Wipe Widget if
enabled, but the value must be positive to make this widget
- Grad Angle: Default: 0, Range: any.
The direction of the wipe gradient in
degrees. This will have no effect unless Grad Add
is positive. The Wipe Widget also allows adjusting this parameter.
Popup menu, Default: Normal.
Determines the method used for dealing with
- All Opaque: Use this option to render slightly faster when
the input image is fully opaque with no transparency (alpha=1).
- Normal: Process opacity normally.
- As Premult: Process as if the image is already in
premultiplied form (colors have been scaled by opacity). This option
also renders slightly faster than Normal mode, but the results will
also be in premultiplied form, which is sometimes less correct.
- Show Wipe: Check-box, Default: off.
Turns on or off the screen user interface widget
for adjusting the Grad Add, Grad Angle, and Wipe Percent parameters. The
value of the Grad Add parameter must first be positive for this
widget to be visible.This parameter only appears on AE and Premiere,
where on-screen widgets are supported.
© 2007, GenArts, Inc. All rights reserved.